Vehicles
Sections
424 not categorized PORSCHE CAYENNE TURBO GERMANYCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: CAYENNE 2011-14 (includes uncategorized and accessory items) FVD123001 If you are experiencing over boost, odds are your wastegate diaphragm is torn or leaking. We are finding more and more failures on these diaphragms with our classics. We strongly recommend replacing them with the addition of an upgraded boost spring, part # FVD123110 . We also recommend replacing the pressure switch, part # 93060610100 high quality, German made, turbocharger wastegate diaphragm membrane. Sold individually. 1 necessary per car.
$133.10
Make a selection FVD123002 This is a factory series borg warner / kkk k27 turbocharger. It is a direct replacement for part # 930 123 003 01 which is currently no longer available from the factory. We source this from an OEM supplier with exacting standards in Germany. Features: restore factory performance direct replacement includes turbocharger hose 93011036801eq includes hose clamps sold individually. 1 necessary per car. Please note: there is no applicable core charge on this turbo. We send you a newly remanufactured unit with hose and clamps.
$3,285.88
Make a selection 99660610502 997 turbo/gt2 only for 6-speed manual transmission
From $207.90
Make a selection 270503055 High-quality OEM front chin spoiler kit replacement that includes all necessary installation hardware. We source this part in Germany to ensure quality, reliability and precise fitment. Kit includes: qty. 1 front chin spoiler 930 / 911 wide body / turbo look 1975-89 - 93050305501 qty. 11 spoiler shim - 91150302300 qty. 1 left spoiler mounting plate qty. 1 right spoiler mounting plate qty. 15 m6 stainless nuts qty. 15 m6 washers sold individually. 1 needed per car.
$2,001.90
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD123047ATK FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$2,634.50
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection FVD34350503 Turbo / 968 nur ohne m030 / sportfahrwerk
$47.30
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection FVD351997TTCS1 This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$5,871.80
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD3522946993R Genuine rear "big red" brake kit which includes 993 turbo calipers, discs, pads, damping plates, warning contacts and hex head mounting bolts. Please note: this kit requires you to reuse your original emergency brake and dust shield.
$3,681.37
Make a selection FVD351997TTCS This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,344.80
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$874.50
Make a selection FVD50599701MM For all Porsche 997 Carrera models with the standart front bumper! The mounting is very easy. With some screwing points under the Porsche front bumper. Not for models with the aerokit or turbo | GT2 | GT3 front bumper
$1,042.80
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD51299701MM Rear diffuser for all Porsche 997.1 Carrera models. The mounting is very easy. Plug & play with 3M double tape and 2 screws on the screwing points. Not for models with the turbo | GT2 | GT3 rear bumper
$1,312.30
Make a selection FVD512991TT01 The moshammer rear wing spoiler lip is a bold, aggressive design that maximizes downforce. The rear spoiler lip installs seamlessly without drilling and the Porsche active rear spoiler remains fully functional. This is the perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs (991.1 turbo/s) packages, the result is a confident, cohesive stance with balanced downforce. Features: aggressive design increased rear downforce improved handling simple to install and remove lightweight composite material designed and manufactured in Germany FVD Brombacherhas a tradition of ...(choose a part on the right to read more)
$1,383.80
Make a selection FVD631997LEDUS Us version. Looking for the latest 997.2 led lighting for you 997.1? We have the solution. Now you can purchase Porsche factory tail lights and install seamlessly with our led conversion units. Description: - can be used with Porsche OEM factory tail lights (us version) - will not trigger warning lights - works seamlessly with Bosch electronic control unit (no need for additional load resistors) - simple plug and play installation warning this will not work on 2009 997.1 turbos!
$544.50
Make a selection FVD512997GT3RST 997 GT3 rear spoiler fits 997turbo includes: deck lid, aluminum upright, 3rd brake light housing and kevlar/carbone wing (l= 145cm, b=28cm, h=7 cm) with end plates. Material: aluminum, fiberglass, kevlar-carbone. Also available with wing blade in fiber (gfk) FVD512997gt3rs tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x
$6,528.50
Make a selection FVD721883081 High quality, German made brake bleeder and vacuum pump kit. Ideal for use on brakes, clutches, hvac, bleeding the fuel system or testing vacuum on a turbocharged system. Vacuum can be tested up to 0.9 bar and pressure up to 4 bar. The kit is complete with a variety of hose ends for various connections. Sold individually. General FitmentACCESSORY
From $246.40
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,094.50
Make a selection FVD95861880MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 309kw (420hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 256km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,0s tuning: max. Power - 325kw (442hp) @ 6000rpm max. Torque - 530nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,484.16
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |